Safety defect investigations, technical specifications, and manufacturer repair notices for Canadian owners.
Enter a VIN to identify your vehicle and find Canadian recall notices that may apply to its make, model and year. Confirm VIN-specific eligibility and repair status with the manufacturer.
Switch to another BMW 7 Series model year.
Safety recall notices and repair campaigns registered for the 1993 BMW 7 Series in Canada.
On certain vehicles, failure of a cooling system component such as thermostat, water pump or fan belt can result in a significant increase in coolant temperature and system pressure. Increased system pressure could result the formation of a crack or separation of a seam in the heater core end piece which would cause hot coolant to be expelled from the heater core. This hot fluid could contact car occupants resulting in possible personal injury and/or fogging of the interior window surfaces. Correction: Radiator cap will be replaced with a new design cap in order to avoid buildup of excessive pressure in the cooling system.
A failure of this component (heater and defroster) may increase the risk of a crash or injury.
Authorized dealerships will inspect the vehicle and complete all necessary repairs free of charge (parts and labor).
On certain 318IC, 318IS, 318TI, 325I, 325IC, 325IS, 525I, 525IT, 530I, 530IT, 540I, 740I, 740IL, 840CI and M3, the cruise control and throttle cable are attached to the same throttle valve actuating lever at the throttle housing. It is possible that the plastic bushing on either cable could break causing the outer cable housing to separate from the bushing. Throttle pedal application without cruise control engagement could cause the outer tube to catch on the edge of the broken bushing resulting in the throttle valve remaining partially open. If this were to occur, the car might not decelerate as expected and a crash could occut. Correction: A spring clip will be installed on the outer tube of each cable to prevent dislodgment from the bushing.
A failure of this component (engine) may increase the risk of a crash or injury.
Authorized dealerships will inspect the vehicle and complete all necessary repairs free of charge (parts and labor).
On certain 325I, 325IC, 325IS, 525I, 525IT, 530I, 530IT, 535I, 540I, 735I, 735IL, 740I, 740IL and 750I, the brake light switch may fail due to a reduction of contact force on the "snap contact" system which the switch incorporates. This could cause heat induced distortion of the plastic internal switch parts in the area of the electrical contacts. This could cause the switch to remain either in the ON or the OFF position resulting in the brake lights being continuously illuminated or inoperative regardless of brake pedal operation. Correction: Switch will be replaced with on that utilizes a different contact system.
A failure of this component (lights and instruments) may increase the risk of a crash or injury.
Authorized dealerships will inspect the vehicle and complete all necessary repairs free of charge (parts and labor).
On certain 318I, 318IC, 318IS, 325IC, 325IS, 325IX, 525I, 535I, 735I and 735IL vehicles, the fuel feed hose could harden and "set" over time due to engine compartment temperatures. If this "setting" occurs, it is possible that seepage between the hose and fitting could result because the clamp cannot provide sufficient sealing force to compensate for the hardening of the hose. Fuel seepage, in the presence of an ignition source, could result in an engine compartment fire. Correction: fuel feed hoses and associated clamps will be replaced with ones of a new design.
A failure of this component (fuel system) may increase the risk of a crash or injury.
Authorized dealerships will inspect the vehicle and complete all necessary repairs free of charge (parts and labor).
On certain 740IA and 740ILA vehicles, the inner throttle cable could break due to a smaller than specification bend in the cable tube. If this were to occur, throttle control would be lost and the engine would return to or remain at idle. Correction: Throttle cable will be replaced with one meeting BMW specifications.
A failure of this component (engine) may increase the risk of a crash or injury.
Authorized dealerships will inspect the vehicle and complete all necessary repairs free of charge (parts and labor).
Official Transport Canada safety campaigns, Canadian motor vehicle safety compliance standards and live VIN specifications.
Explore safety recall records by model year.