Safety defect investigations, technical specifications, and manufacturer repair notices for Canadian owners.
Enter a VIN to identify your vehicle and find Canadian recall notices that may apply to its make, model and year. Confirm VIN-specific eligibility and repair status with the manufacturer.
Switch to another Ford F-550 Chassis Cab model year.
Safety recall notices and repair campaigns registered for the 2017 Ford F-550 Chassis Cab in Canada.
On certain vehicles, there could be a problem with the connections inside the rearview camera. As a result, the rearview camera image may not display correctly or at all when the transmission is shifted into reverse. Note: For certain models, this recall also affects incomplete vehicles.
A rearview camera image that doesn't display could reduce a driver's ability to see behind the vehicle while backing up. This could increase the risk of a crash.
Ford will notify owners by mail and advise you to take your vehicle to a dealership to inspect and, if necessary, replace the rearview camera.
On certain vehicles, door latch shielding may not be sufficient. As a result, water could enter into the side door latch and freeze, causing the latch mechanism to bind after opening. In addition, latch actuation cables may have been bent or kinked during installation, and could result in latch binding. A frozen door latch, or bent or kinked actuation cable may result in a door that will not open or will not close. If a latch does not fully engage the door striker, there is a potential for a door to open while the vehicle is in motion, which could increase the risk of injury. Correction: Dealers will install water shields over the door latches and the door latch actuation cables will be inspected and repaired if needed.
A failure of this component (structure) may increase the risk of a crash or injury.
Authorized dealerships will inspect the vehicle and complete all necessary repairs free of charge (parts and labor).
Certain vehicles equipped with a manual-recline driver seat may fail to conform to Canada Motor Vehicle Safety Standard (CMVSS) 202 - Head Restraints and CMVSS 207 - Anchorage of Seats. Due to a manufacturing error, the recliner mechanism may have been incorrectly welded to the seat-back frame, which would result in the seat failing to meet the requirements of the standards. This could increase the risk of injury to the seat occupant in the event of a crash. Correction: Dealers will inspect the front driver seat back frame build date and replace as necessary.
A failure of this component (seats and restraints) may increase the risk of a crash or injury.
Authorized dealerships will inspect the vehicle and complete all necessary repairs free of charge (parts and labor).
Certain decorative chrome door handle covers, sold as aftermarket accessories through Ford dealers, may affect compliance to Canada Motor Vehicle Safety Standard (CMVSS) 206 – Door Lock and Door Retention Components. These accessories may cause the door handles to fail to conform to the inertial load requirements of the standard. A door handle fitted with a chrome cover could unlatch due to inertial loads during a side impact crash if the door were unlocked, which would increase the risk of injury. Correction: Covers will be removed from vehicles and owners will be reimbursed for parts and labour.
A failure of this component (accessories) may increase the risk of a crash or injury.
Authorized dealerships will inspect the vehicle and complete all necessary repairs free of charge (parts and labor).
Certain vehicles equipped with a 6.8L gasoline engine, 4x4 drive, 205” wheel base and 4.88 axle ratio may experience a driveline vibration caused by a powertrain resonance at speeds above 120 km/h. Continued operation of a vehicle at these speeds could result in a resonance frequency that may fracture transmission and/or driveline components. If the transmission and or driveline components were to fracture, it could result in a loss of motive power while the vehicle is in motion, or unintended vehicle movement in Park if the parking brake is not applied, which would increase the risk of a crash causing injury and/or damage to property. Correction: Dealers will replace the two-piece driveshaft with a new three-piece driveshaft and two center bearing brackets.
A failure of this component (powertrain) may increase the risk of a crash or injury.
Authorized dealerships will inspect the vehicle and complete all necessary repairs free of charge (parts and labor).
Official Transport Canada safety campaigns, Canadian motor vehicle safety compliance standards and live VIN specifications.
Explore safety recall records by model year.