Safety defect investigations, technical specifications, and manufacturer repair notices for Canadian owners.
Enter a VIN to identify your vehicle and find Canadian recall notices that may apply to its make, model and year. Confirm VIN-specific eligibility and repair status with the manufacturer.
Switch to another Freightliner 108sd model year.
Safety recall notices and repair campaigns registered for the 2016 Freightliner 108sd in Canada.
Certain trucks were built with tires that are not approved for use with the truck's wheels. As a result, the tires may not perform properly, or a tire could fail.
A tire failure could cause a loss of control and increase the risk of a crash.
Daimler Trucks North America (DTNA) will notify owners by mail. The corrective actions for this recall are under development. You will be instructed to bring your truck to a DTNA authorized service facility when a repair is available.
On certain trucks equipped with electronic stability control (ESC), the brake lights may turn on when the automatic traction control (ATC) activates. Canadian regulations do not allow brake lights to turn on when the automatic traction control activates.
Brake lights that turn on when a vehicle is not slowing could confuse other drivers.
The company will notify owners by mail and instruct them to take their truck to a Daimler Trucks North America authorized service facility. The truck will either be reprogrammed or retrofitted so the brake lights do not turn on when the automatic traction control (ATC) activates.
Certain trucks were built with air reservoir tanks that are too small in relation to the size of the air brake chambers. Canadian regulations require enough air reservoir capacity to ensure the brakes work even with heavy use or when there is a partial loss of the air system.
Reduced braking could cause extended stopping distances and increase the risk of a crash.
The company will notify owners by mail and instruct them to take their truck to a Daimler Trucks North America authorized service facility to modify the truck to ensure it meets Canadian regulations.
On certain vehicles, the required check valve may not have been installed in one of the ports of the spring brake modulation valve. In the event of a rapid loss of air pressure in the secondary system, the missing check valve could cause a similar rapid loss of pressure in the primary system, which may lead to a sudden application of the parking brakes. This could increase the risk of a crash causing injury and/or damage to property. Correction: Daimler Trucks North America authorized service facilities will inspect and the check valve will be installed if needed.
A failure of this component (brakes) may increase the risk of a crash or injury.
Authorized dealerships will inspect the vehicle and complete all necessary repairs free of charge (parts and labor).
On certain vehicles, the specified front axle weight limit may be greater than the hub capacity. If the axle load exceeds the maximum weight capacity of the hub, there is an increased risk of hub fatigue, which could cause a complete separation of the wheel(s) and a loss of vehicle control, increasing the risk of a crash causing injury and/or damage to property. Correction: Dealers will replace the incorrectly specified front axle hubs.
A failure of this component (wheels) may increase the risk of a crash or injury.
Authorized dealerships will inspect the vehicle and complete all necessary repairs free of charge (parts and labor).
On certain vehicles, the rear disk brake calipers may contact the spring suspension due to incorrect caliper orientation. This could reduce rear brake effectiveness which would result in increased stopping distances, increasing the risk of a crash causing injury and/or damage to property. Correction: Dealers will correct the orientation of the rear calipers.
A failure of this component (brakes) may increase the risk of a crash or injury.
Authorized dealerships will inspect the vehicle and complete all necessary repairs free of charge (parts and labor).
On certain vehicles built with a front axle built by Detroit Axles, the steering arm bolt may not have been sufficiently tightened at time of assembly. This could allow the bolt to loosen and potentially result in the separation of the steering arm from the steering knuckle, which could result in a loss of steering. This could increase the risk of a crash causing injury and/or damage to property. Correction: Dealers will inspect the bolt torque and re-tighten or replace as necessary.
A failure of this component (steering) may increase the risk of a crash or injury.
Authorized dealerships will inspect the vehicle and complete all necessary repairs free of charge (parts and labor).
Official Transport Canada safety campaigns, Canadian motor vehicle safety compliance standards and live VIN specifications.
Explore safety recall records by model year.