2018 Freightliner 108sd Recall

Certain trucks were built with tires that are not approved for use with the truck's wheels. As a result, the tires may not perform properly, or a tire could fail.

A tire failure could cause a loss of control and increase the risk of a crash.

Daimler Trucks North America (DTNA) will notify owners by mail. The corrective actions for this recall are under development. You will be instructed to bring your truck to a DTNA authorized service facility when a repair is available.

On certain vehicles, the fuel rail assembly could develop a leak. Note: This recall only affects vehicles equipped with a Cummins L9 or ISX12 diesel engine.

A fuel leak can create the risk of a fire.

Cummins will notify owners by mail and instruct you to take your vehicle to a Cummins authorized service center to inspect the fuel rail. If damage is found, the fuel rail and fuel lines will be replaced. If no damage is found, the fuel rail will be reassembled with new crush washers using a special tool.

On certain trucks equipped with an Eaton automated manual transmission and electronic clutch actuator (ECA), a component within the clutch assembly could fail. If this happens, the broken clutch components could prevent the transmission from disengaging or shifting to neutral. This could result in unintended vehicle movement, even if the parking brake is applied. Note: This recall replaces FL-803 (Transport Canada recall 2018-714). Trucks that were repaired under that recall also require this repair.

Sudden and unexpected movement of the vehicle could create a risk of injury or a crash.

Daimler Trucks North America (DTNA) will notify owners by mail and instruct you to take your truck to a DTNA authorized service facility to replace the clutch and update the transmission software.

On certain trucks, the engine wire harness could be damaged by contact with various locations around the air compressor and the frame rail. If this happens, the engine could stall and you may not be able to restart it. Note: This recall only affects trucks built with a Detroit DD8 engine.

A sudden loss of engine power could increase the risk of a crash.

Daimler Trucks North America (DTNA) will notify owners by mail and instruct you to take your truck to a DTNA authorized service facility to inspect the clearance between the wire harness and engine, and to check for any damage to the wiring. If the wire harness is damaged, it will be replaced with a new harness that has a severe duty wrap and additional hardware for routing.

On certain trucks equipped with electronic stability control (ESC), the brake lights may turn on when the automatic traction control (ATC) activates. Canadian regulations do not allow brake lights to turn on when the automatic traction control activates.

Brake lights that turn on when a vehicle is not slowing could confuse other drivers.

The company will notify owners by mail and instruct them to take their truck to a Daimler Trucks North America authorized service facility. The truck will either be reprogrammed or retrofitted so the brake lights do not turn on when the automatic traction control (ATC) activates.

Certain trucks were built with air reservoir tanks that are too small in relation to the size of the air brake chambers. Canadian regulations require enough air reservoir capacity to ensure the brakes work even with heavy use or when there is a partial loss of the air system.

Reduced braking could cause extended stopping distances and increase the risk of a crash.

The company will notify owners by mail and instruct them to take their truck to a Daimler Trucks North America authorized service facility to modify the truck to ensure it meets Canadian regulations.

On certain vehicles, the bolts that join the steering and tie rod arm to the steering knuckle may not have been properly tightened. This could lead to a separation of the tie rod arm and cause a loss of steering control. This could create a risk of a crash causing injury and/or property damage. Correction: Daimler Trucks North America Authorized Service Facilities will inspect the steering and tie rod arm bolts to ensure they are torqued correctly and install new fasteners as necessary.

A failure of this component (steering) may increase the risk of a crash or injury.

Authorized dealerships will inspect the vehicle and complete all necessary repairs free of charge (parts and labor).

This recall was replaced by Transport Canada Recall No. 2020-488. On certain vehicles equipped with an Eaton automated manual transmission and electronic clutch actuator (ECA), an internal component within the clutch assembly may have been manufactured improperly and could fail. If this occurs, the broken clutch components could prevent the transmission from disengaging or shifting to neutral. This could result in unintended vehicle movement, even if the parking brake is applied, increasing the risk of a crash causing injury and/or damage to property. Correction: Daimler Trucks of North America Authorized Service Facilities will recalibrate the Transmission Control Module (TCM) and replace components as necessary.

A failure of this component (powertrain) may increase the risk of a crash or injury.

Authorized dealerships will inspect the vehicle and complete all necessary repairs free of charge (parts and labor).

On certain vehicles equipped with air disc brakes, the brake caliper mounting bolts may be incorrectly torqued. This could result in the caliper bolts loosening, which could lead to the caliper detaching. Insufficiently torqued fasteners may not provide adequate clamping force between the brake caliper and brake anchor plate potentially resulting in reduced brake effectiveness, which would result in increased stopping distances, increasing the risk of a crash causing injury and/or damage to property. Correction: Daimler Trucks of North America Service Facilities will inspect the bolts, and repair as necessary.

A failure of this component (brakes) may increase the risk of a crash or injury.

Authorized dealerships will inspect the vehicle and complete all necessary repairs free of charge (parts and labor).

On certain trucks, the steering shaft assembly may not have been installed correctly. This could cause a loss of connection between the steering wheel and the front wheels, resulting in a loss of steering control and creating the risk of a crash causing injury and/or damage to property. Correction: Daimler Trucks North America Authorized Service Facilities will inspect the steering shaft assembly and repair as necessary. Note: This is an expansion of recall 2018-386.

A failure of this component (steering) may increase the risk of a crash or injury.

Authorized dealerships will inspect the vehicle and complete all necessary repairs free of charge (parts and labor).

On certain vehicles, the required check valve may not have been installed in one of the ports of the spring brake modulation valve. In the event of a rapid loss of air pressure in the secondary system, the missing check valve could cause a similar rapid loss of pressure in the primary system, which may lead to a sudden application of the parking brakes. This could increase the risk of a crash causing injury and/or damage to property. Correction: Daimler Trucks North America authorized service facilities will inspect and the check valve will be installed if needed.

A failure of this component (brakes) may increase the risk of a crash or injury.

Authorized dealerships will inspect the vehicle and complete all necessary repairs free of charge (parts and labor).