Safety defect investigations, technical specifications, and manufacturer repair notices for Canadian owners.
Enter a VIN to identify your vehicle and find Canadian recall notices that may apply to its make, model and year. Confirm VIN-specific eligibility and repair status with the manufacturer.
Switch to another GMC Sierra model year.
Safety recall notices and repair campaigns registered for the 1999 GMC Sierra in Canada.
On certain vehicles, the galvanized-braided-steel tailgate support cables used to support the tailgate in the full open (horizontal) position can corrode over time and fracture when loads are applied to them. Tailgate support cable corrosion may not be visible because of the plastic sheathing covering the cable. If one cable fractured, the remaining cable may retain the tailgate in a horizontal position. If the remaining cable was weakened by corrosion, it could fracture within moments of the first cable fracture. If both cables fractured, the tailgate would suddenly drop approximately 10 degrees and strike the top surface of the rear bumper. If anyone is sitting or standing on the horizontal surface of the tailgate when both cables fracture, they could fall and be injured. On vehicles without a rear bumper, the tailgate may drop to a lower position. Correction: Dealers will replace the existing galvanized support cables with stainless steel support cables.
A failure of this component (other) may increase the risk of a crash or injury.
Authorized dealerships will inspect the vehicle and complete all necessary repairs free of charge (parts and labor).
On certain 1999-2002 1500 series and 2001-2005 2500 & 3500 series trucks equipped with a manual transmission, the parking brake friction lining may wear to an extent where the parking brake can become ineffective in immobilizing a parked vehicle. Correction: Dealers will install a low-force spring clip retainer on vehicles equipped with PBR parking brake system and install a redesigned parking brake cable assembly on vehicle equipped with a TRW parking brake system.
A failure of this component (brakes) may increase the risk of a crash or injury.
Authorized dealerships will inspect the vehicle and complete all necessary repairs free of charge (parts and labor).
Certain vehicles located in Ontario, Quebec, New Brunswick, Nova Scotia, Prince Edward Island, and Newfoundland & Labrador may experience unwanted Antilock Brake System (ABS) activation and increased stopping distances during low-speed brake application (less than 16 km/h and greater than 6 km/h). This condition does not set any ABS codes nor does it illuminate the ABS warning lamp. Correction: Dealers will remove the wheel speed sensor and thoroughly clean the wheel speed sensor mounting surface on the bearing, apply Zinc-X to the cleaned surface, grease the mounting surface, reinstall the wheel speed sensor, and check the output voltage to ensure the wheel speed signal is within specifications.
A failure of this component (brakes) may increase the risk of a crash or injury.
Authorized dealerships will inspect the vehicle and complete all necessary repairs free of charge (parts and labor).
Certain vehicles: Light duty trucks. passenger vehicles and sport utility vehicles. Certain vehicles do not comply with the requirements of C.M.V.S.S. NO. 118, "POWER-OPERATED WINDOW, PARTITION & ROOF PANEL SYSTEMS." When the hazard flasher switch is used to turn the hazard flashers on or off, the retained accessory power (RAP) feature can be activated without a key in the ignition. Correction: There is no detrimental effect on vehicle safety so no corrective action is necessary.
A failure of this component (electrical) may increase the risk of a crash or injury.
Authorized dealerships will inspect the vehicle and complete all necessary repairs free of charge (parts and labor).
On certain vehicles, the body cross sill may contact the front, right-hand brake pipe. This could eventually wear a hole in the brake pipe over the normal life of the vehicle and result in a brake fluid leak. This could ultimately result in a partial brake system failure and increased stopping distances. Correction: Dealers will inspect for brake pipe wear and replace worn section if necessary. A spacer clip will be installed to ensure adequate clearance.
A failure of this component (brakes) may increase the risk of a crash or injury.
Authorized dealerships will inspect the vehicle and complete all necessary repairs free of charge (parts and labor).
Certain vehicles do not comply with the requirements of CMVSS 209 - Seat Belt Assemblies. These vehicles have front belt retractors that have higher G-force lock-up levels than those required by the standard. In addition, some retractors could have internal damage that could cause a "no-lock" condition. In the event of a vehicle crash, these conditions could result in increased occupant injury. Correction: Driver and passenger seat belt retractors will be replaced.
A failure of this component (seats and restraints) may increase the risk of a crash or injury.
Authorized dealerships will inspect the vehicle and complete all necessary repairs free of charge (parts and labor).
Certain vehicles equipped with 4.8 litre or 5.3 litre engines do not comply with the requirements of CMVSS 1103 - Exhaust Emissions. Engines may have been built with the wrong Linear Exhaust Gas Recirculation (LEGR) valve which could limit the required air flow rate. A failed valve could cause the vehicle to fail to meet applicable emissions standards. Correction: Vehicles will be inspected and LEGR valve will be replaced with a new valve where required.
A failure of this component (emissions) may increase the risk of a crash or injury.
Authorized dealerships will inspect the vehicle and complete all necessary repairs free of charge (parts and labor).
Certain vehicles have lower than specified torque on all three of the steering gear to frame attachment bolts. In this condition, the bolts may loosen during the life of the vehicle. Relative movement of the steering gear to frame may wear and/or fatigue the attaching bolts to the point of breakage or the bolts backing out. This would result in steering gear separation and loss of steering control. Correction: Steering gear to frame bolts will be torqued to the proper specification.
A failure of this component (steering) may increase the risk of a crash or injury.
Authorized dealerships will inspect the vehicle and complete all necessary repairs free of charge (parts and labor).
Official Transport Canada safety campaigns, Canadian motor vehicle safety compliance standards and live VIN specifications.
Explore safety recall records by model year.