2015 GMC Yukon Recall

On certain vehicles, there may be an error in the electronic-brake control module software. This could cause the driveline-protection system to activate when a wheel-speed sensor fails. If this happens, the brakes could apply and cause the vehicle to pull to one side. Note: This recall only affects vehicles equipped with four-wheel drive, a 5.3-L engine, and a 3.08 ratio rear axle. The problem can only occur when the vehicle is in four-wheel drive or automatic mode, and travelling at a speed between 66 and 97 km/h (41 and 60 mph). A wheel-speed sensor failure will cause the electronic stability control (ESC) and anti-lock braking system (ABS) warning lights to turn on, and a "Service StabiliTrak" message to display.

A vehicle that suddenly pulls to one side could increase the risk of a crash.

General Motors will notify owners by mail and instruct you to take your vehicle to a dealer to update the electronic-brake control module software. General Motors advises that using two-wheel-drive mode can eliminate the risk until the recall repair is completed.

This recall is for aftermarket replacement rear window glass produced by Vitro Automotriz. Certain rear window glass may not have been properly tempered. If the window breaks, the glass may separate into large pieces instead of very small ones. Note: This is a voluntary recall that is not being conducted under the requirements of the Motor Vehicle Safety Act.

Glass that breaks in to large pieces could create a risk of injury.

The company will notify consumers by mail and instruct them to inspect the designation code marked on the rear window glass. Products affected by this recall have the designation “DOT 287” along with the lettering “VMR” (Replacement Market) and a date code that is before July 2019. This information is printed on the bottom corner of the glass. Consumers should contact Vitro's customer service at 1-412-995-6457 or argbacklites@vitro.com to arrange for replacement of the glass.

On certain vehicles, there could be a reduction in power brake assist due to a decrease in output from the vacuum pump. This could cause a hard brake pedal and an increase in brake pedal effort to stop the vehicle.

A sudden increase in brake pedal force could lead to an increase in stopping distance. This could increase the risk of a crash.

The company will notify owners by mail and instruct them to take their vehicle to a dealer to reprogram the electronic brake control module.

Certain vehicles may experience a temporary loss of electric power steering (EPS) assist followed by a sudden return of EPS assist, particularly during low-speed turning manoeuvres due to an electrical/software issue. If EPS assist is lost and suddenly returned, the unexpected change in steering effort could affect vehicle control, which would increase the risk of a crash causing injury and/or damage to property. Correction: Dealers will update the EPS module software. Note: If power steering assist is lost and the vehicle reverts to manual steering, a dash message would be displayed stating there is an EPS problem. Additionally, this issue could also affect radio, stabilitrak, the driver information centre, chime, door-lock, air conditioning, and/or cruise control function.

A failure of this component (steering) may increase the risk of a crash or injury.

Authorized dealerships will inspect the vehicle and complete all necessary repairs free of charge (parts and labor).

On certain vehicles, the sensing and diagnostic module (SDM), which controls airbag and pretensioner deployment, contains a software defect which may prevent the deployment of frontal airbags and pretensioners in certain circumstances. Failure of frontal airbags and seatbelt pretensioners to deploy in a crash (when warranted) could increase the risk of injury. Correction: Dealers will reflash the SDM with new software. In vehicles with any previous deployment events recorded in the SDM, the dealers will replace the existing SDM with a new SDM containing the latest software.

A failure of this component (airbag) may increase the risk of a crash or injury.

Authorized dealerships will inspect the vehicle and complete all necessary repairs free of charge (parts and labor).

On certain vehicles equipped with Continental P275/55R20 CrossContact LX20 tires, a manufacturing defect could cause a lack of adhesion between belts in the tire. Affected tires may exhibit localized tread wear, excessive vibration, noise and bulging in the tread area. Continued use could cause the belts to separate, which could lead to full belt/tread loss. This could increase the risk of a crash causing injury and/or damage to property. Correction: Dealers will inspect tire date code markings to determine whether they are from the affected date code. Affected tires will be replaced.

A failure of this component (tires) may increase the risk of a crash or injury.

Authorized dealerships will inspect the vehicle and complete all necessary repairs free of charge (parts and labor).

On certain vehicles, the sensing and diagnostic module (SDM), which controls airbag and pretensioner deployment, contains a software defect which may prevent the deployment of frontal airbags and pretensioners in certain circumstances. Failure of frontal airbags and seatbelt pretensioners to deploy in a crash (when warranted) could increase the risk of injury. Correction: Dealers will reflash the SDM with new software. In vehicles with any previous deployment events recorded in the SDM, the dealers will replace the existing SDM with a new SDM containing the latest software. Note: This recall affects 2014-2017 model year Sierra LD/Silverado LD models and 2015-2016 model year Sierra HD/Silverado HD model vehicles.

A failure of this component (airbag) may increase the risk of a crash or injury.

Authorized dealerships will inspect the vehicle and complete all necessary repairs free of charge (parts and labor).

On certain vehicles, exhaust components may overheat while the vehicle is idling in cold temperatures. This could cause nearby plastic components to overheat and melt, possibly resulting in smoke and/or fire and increasing the risk of injury and/or damage to property. Correction: Dealers will reprogram the engine control module. Note: This is an expansion of recall 2014-005.

A failure of this component (engine) may increase the risk of a crash or injury.

Authorized dealerships will inspect the vehicle and complete all necessary repairs free of charge (parts and labor).

Certain vehicles may not comply with the requirements of Canada Motor Vehicle Safety Standard 108 - Lighting System and Retroreflective Devices. If the headlamp switch is rapidly and repeatedly cycled between positions (at least two cycles within 0.6 seconds), park lamp and daytime running light function could be disabled, which is contrary to the requirements of the standard. Correction: A production change has been undertaken to remedy this technical non-compliance condition. No corrective recall action is required as the technical non-compliance condition is deemed to be non-safety related.

A failure of this component (lights and instruments) may increase the risk of a crash or injury.

Authorized dealerships will inspect the vehicle and complete all necessary repairs free of charge (parts and labor).

Certain vehicles equipped with an Automatic Transfer Case may have a condition in which an electric signal short may cause the transfer case to switch to neutral without operator input. The transfer case mode selection knob would still indicate the last selected drive mode, but the driver would not have any feedback that the transfer case is in neutral. If the transfer case switches to neutral while the vehicle is in motion, the driver would experience a loss of motive power and, if the vehicle is parked without the parking brake applied, the vehicle could roll away. Both scenarios could result in a crash causing injury and/or damage to property. Correction: Dealers will re-program the software of the Transfer Case Control Module.

A failure of this component (powertrain) may increase the risk of a crash or injury.

Authorized dealerships will inspect the vehicle and complete all necessary repairs free of charge (parts and labor).

Certain vehicles equipped with a base radio and internal amplifier may fail to conform to Canada Motor Vehicle Safety Standard (CMVSS) 114 - Theft Protection and Rollaway Protection, and CMVSS 208 - Occupant Crash Protection. The radio may become inoperative, causing a no-chime condition and disabling the audible warning if the key is in the ignition and the driver’s door is opened, or if a front outboard seat belt is not buckled. A loss of the seat belt audible warning may increase the likelihood of a front outboard occupant being unbelted, increasing the risk of injury in a crash. Similarly, the loss of an audible warning when a key is left in the ignition may increase the risk of vehicle theft. Correction: Dealers are to program the radio with updated software.

A failure of this component (accessories) may increase the risk of a crash or injury.

Authorized dealerships will inspect the vehicle and complete all necessary repairs free of charge (parts and labor).

On certain vehicles equipped with 6 speed automatic transmissions, transmission cooler lines may not have been securely seated in their fittings at time of assembly. This could result in a transmission fluid leak in proximity to hot surfaces which could increase the risk of a fire, potentially causing injury and/or property damage. Correction: Dealers will inspect connections and repair as necessary.

A failure of this component (powertrain) may increase the risk of a crash or injury.

Authorized dealerships will inspect the vehicle and complete all necessary repairs free of charge (parts and labor).