Safety defect investigations, technical specifications, and manufacturer repair notices for Canadian owners.
Enter a VIN to identify your vehicle and find Canadian recall notices that may apply to its make, model and year. Confirm VIN-specific eligibility and repair status with the manufacturer.
Switch to another International 9400 model year.
Safety recall notices and repair campaigns registered for the 1999 International 9400 in Canada.
On certain vehicles, the automatic slack adjuster anchor brackets can fail due to fatigue fracture and completely separate, causing the slack adjusters to function as manual slack adjusters. If the support bracket for an automatic slack adjuster fails, the brakes at that wheel end will not automatically adjust. As the brake linings wear, the vehicle will have reduced braking capacity, increasing the risk of a crash. Correction: Dealers will install a new bracket on each suspect slack adjuster.
A failure of this component (brakes) may increase the risk of a crash or injury.
Authorized dealerships will inspect the vehicle and complete all necessary repairs free of charge (parts and labor).
On certain vehicles, the four bolts that hold the bunk webbing restraint latch brackets to the bunk base may be of an incorrect grade. Grade 5 bolts were used in lieu of the required grade 8 bolts. Grade 5 bolts do not meet the original design intent of the restraint. Correction: Vehicles will be inspected and all grade 5 bolts will be replaced with grade 8 bolts.
A failure of this component (seats and restraints) may increase the risk of a crash or injury.
Authorized dealerships will inspect the vehicle and complete all necessary repairs free of charge (parts and labor).
On certain vehicles, the Antilock Traction Relay Valves manufactured by Bendix were incorrectly assembled. An extra check valve was installed which will not allow the traction control system to function properly. When the system detects a traction control event, the defective valve can cause the rear brakes to apply and not release until the air system pressure is depleted. An unexpected and uncontrollable application of the rear brakes could cause a crash without prior warning. Correction: Suspect vehicles will be inspected and all Antilock Traction Relay Valves found to be defective will be replaced.
A failure of this component (brakes) may increase the risk of a crash or injury.
Authorized dealerships will inspect the vehicle and complete all necessary repairs free of charge (parts and labor).
The knurled pivot shaft (which operates the windshield wiper arm) is welded to a lever, which connects the linkage from the wiper motor. On certain vehicles, the weld at the pivot shaft to lever may fail. This failure can occur on either the right or left side causing the wiper arm to be inoperative for that side. This could result in obscured driver vision if the failure occurred during inclement weather. Correction: A stall test will be performed on the wiper system to validate the integrity of the suspect weld. All wiper assemblies which fail the stall test will be replaced.
A failure of this component (visual system) may increase the risk of a crash or injury.
Authorized dealerships will inspect the vehicle and complete all necessary repairs free of charge (parts and labor).
On certain vehicles, the radius on the cone of the inner wheel bearing was incorrectly machined resulting in improper seating of the cone against the seal flange of the steering knuckle. Improper seating of the bearing can increase the stress level on the steer axle knuckle spindle as well as bearing movement and excessive bearing end play. This can result in premature bearing wear, eventual fatigue failure of the axle spindle and loss of steering control. Correction: Inner wheel bearings will be inspected for proper seating and bearings that do not seat properly will be changed. The axle spindle and bearing cup will also be inspected for any damage and will be changed as required.
A failure of this component (suspension) may increase the risk of a crash or injury.
Authorized dealerships will inspect the vehicle and complete all necessary repairs free of charge (parts and labor).
On certain vehicles, the automatic slack adjusters may have had insufficient torque applied to the guide pawl cap screw. This condition may cause the brakes to gradually lose adjustment. This could result in loss of brake effectiveness and increased stopping distances which could in turn result in a vehicle crash. Correction:: The torque will be checked on the automatic slack adjuster guide pawl.. If there is no torque, the brakes will be adjusted and the guide pawl will be tightened to 15-20 ft. lbs.
A failure of this component (brakes) may increase the risk of a crash or injury.
Authorized dealerships will inspect the vehicle and complete all necessary repairs free of charge (parts and labor).
Certain vehicles may have experienced loosening of the end yoke retaining nut. If this condition occurs, the driveline can vibrate and separate from the vehicle, causing vehicle damage or personal injury or both. Correction: Center bearing package and coupler shaft will be replaced with a new coupler shaft and a 60mm center bearing package.
A failure of this component (powertrain) may increase the risk of a crash or injury.
Authorized dealerships will inspect the vehicle and complete all necessary repairs free of charge (parts and labor).
Official Transport Canada safety campaigns, Canadian motor vehicle safety compliance standards and live VIN specifications.
Explore safety recall records by model year.