Safety defect investigations, technical specifications, and manufacturer repair notices for Canadian owners.
Enter a VIN to identify your vehicle and find Canadian recall notices that may apply to its make, model and year. Confirm VIN-specific eligibility and repair status with the manufacturer.
Switch to another Mitsubishi Mirage model year.
Safety recall notices and repair campaigns registered for the 2014 Mitsubishi Mirage in Canada.
This service campaign is for certain replacement rear brake drums that were sold by Mitsubishi dealers. The brake drums may have been made with wheel stud holes that are too large. As a result, a wheel stud could spin when tightening the wheel nut. This can reduce the clamping force between the wheel and the brake drum. If this happens, the wheel may eventually come loose and could separate from the vehicle. Note: This service campaign is not being conducted under the requirements of the Motor Vehicle Safety Act.
A wheel that cannot be properly tightened could increase the risk of a wheel separation. This could increase the risk of a crash. A wheel that separates could also hit another person or vehicle.
Mitsubishi will contact owners that may have had these brake drums replaced at a Mitsubishi dealer. They will advise affected owners to take their vehicle to a dealer, who will replace any affected brake drum(s).
On certain vehicles, the wiring harness connector located in the area of the drivers footrest could corrode due to exposure to melted snow/water containing road salt. This could result in illumination of several warning lamps including the Supplemental Restraint System (SRS) warning lamp. If the SRS warning lamp is illuminated and the vehicle is subsequently involved in a collision that warrants frontal air bag deployment, the timing of the frontal airbag deployment(s) may be delayed, which would increase the risk of injury to the seat occupant(s). Correction: Dealers will relocate the wiring connector to a higher position. The connector will also be inspected and, if any corrosion is found, the connector will be replaced with a new one. Note: This recall supersedes recall 2015-579. Vehicles repaired as part of the previous recall will require re-inspection and repair.
A failure of this component (airbag) may increase the risk of a crash or injury.
Authorized dealerships will inspect the vehicle and complete all necessary repairs free of charge (parts and labor).
On certain vehicles, the internal self-diagnostic of the airbag control module may interpret vibrations caused by severe road conditions and/or driving on a flat tire as being a system fault. This would disable the airbag system. As a result, the airbags would not deploy in a crash that warrants their deployment, which would increase the risk of injury. Correction: Dealers will update vehicle software.
A failure of this component (airbag) may increase the risk of a crash or injury.
Authorized dealerships will inspect the vehicle and complete all necessary repairs free of charge (parts and labor).
On certain vehicles, the wiring harness connector located in the area of the drivers footrest could corrode over time due to repeated exposure to melted snow/water containing road salt. This could eventually result in illumination of several warning lamps including the Supplemental Restraint System (SRS) warning lamp. If the SRS warning lamp is illuminated and the vehicle is subsequently involved in a collision that warrants frontal air bag deployment, the timing of the frontal airbag deployment(s) may be delayed, which would increase the risk of injury to the seat occupant(s). Correction: Dealers will install a waterproof sheet to prevent potential contamination and corrosion of the connector. The connector will also be inspected and, if any corrosion is found, the connector will be replaced with a new one.
A failure of this component (electrical) may increase the risk of a crash or injury.
Authorized dealerships will inspect the vehicle and complete all necessary repairs free of charge (parts and labor).
On certain vehicles, due to improper manufacturing, the electrical resistance inside the impact sensor for the Supplemental Restraint System (SRS) air bag system may have increased. As a result, abnormal communication may be detected by the ECU causing the SRS warning lamp to illuminate. If a vehicle is involved in a collision that warrants front, side, and/or curtain air bag deployment when the SRS warning lamp is illuminated, frontal air bag deployment could be delayed and/or the side and curtain air bag may not deploy. Failure of an airbag to deploy during a crash (where deployment is warranted) could increase the risk of injury. Correction: Dealers will replace the SRS impact sensor with a countermeasure unit.
A failure of this component (airbag) may increase the risk of a crash or injury.
Authorized dealerships will inspect the vehicle and complete all necessary repairs free of charge (parts and labor).
Official Transport Canada safety campaigns, Canadian motor vehicle safety compliance standards and live VIN specifications.
Explore safety recall records by model year.