Safety defect investigations, technical specifications, and manufacturer repair notices for Canadian owners.
Enter a VIN to identify your vehicle and find Canadian recall notices that may apply to its make, model and year. Confirm VIN-specific eligibility and repair status with the manufacturer.
Switch to another Sterling L-Line model year.
Safety recall notices and repair campaigns registered for the 2008 Sterling L-Line in Canada.
Certain trucks were built with air reservoir tanks that are too small in relation to the size of the air brake chambers. Canadian regulations require enough air reservoir capacity to ensure the brakes work even with heavy use or when there is a partial loss of the air system.
Reduced braking could cause extended stopping distances and increase the risk of a crash.
The company will notify owners by mail and instruct them to take their truck to a Daimler Trucks North America authorized service facility to modify the truck to ensure it meets Canadian regulations.
On certain trucks, the plastic low-pressure fuel line between the engine-mounted fuel filter and the engine block may develop a diesel fuel leak. The location of the leak is unlikely to result in a vehicle fire; however, diesel fuel spilt on the roadway could endanger other road users by making the roadway unexpectedly slippery. This could ultimately result in a vehicle crash causing property damage and/or personal injury. Correction: Dealers will replace the plastic low-pressure fuel line with a steel version.
A failure of this component (fuel system) may increase the risk of a crash or injury.
Authorized dealerships will inspect the vehicle and complete all necessary repairs free of charge (parts and labor).
On certain trucks equipped with a DD15 or DD16 engine, the bolt attaching a rubber isolator to a support bracket may become loose, back out, and contact the starter cable. This could cause an electrical short, which could result in a fire causing property damage and/or personal injury. Correction: Dealers will install a new bolt and isolator, and apply thread-locking fluid to the fastener.
A failure of this component (electrical) may increase the risk of a crash or injury.
Authorized dealerships will inspect the vehicle and complete all necessary repairs free of charge (parts and labor).
On certain vehicles equipped with a Caterpillar C15 engine, the Variable Valve Actuation (VVA) oil line may wear against the P-clip retaining the oil line. An oil leak could result in a vehicle fire causing property damage and/or personal injury. Correction: Caterpillar dealers will replace the VVA oil line with an updated version.
A failure of this component (engine) may increase the risk of a crash or injury.
Authorized dealerships will inspect the vehicle and complete all necessary repairs free of charge (parts and labor).
On certain trucks, the Diesel Particulate Filter (DPF) chassis attachment bracket may fail, allowing the DPF assembly to separate from the vehicle. Should this occur, the DPF could become a road hazard, posing a risk to motorists and bystanders. Correction: Dealers will replace the DPF chassis attachment bracket and straps.
A failure of this component (emissions) may increase the risk of a crash or injury.
Authorized dealerships will inspect the vehicle and complete all necessary repairs free of charge (parts and labor).
On certain trucks, the Aftertreatment Regeneration Device (ARD) may develop a hole, allowing heat and flame to escape during a regeneration of the Diesel Particulate Filter (DPF). This could result in a fire, causing property damage, personal injury or death. Correction: Dealers will replace the ARD body and, if necessary, upgrade the software.
A failure of this component (emissions) may increase the risk of a crash or injury.
Authorized dealerships will inspect the vehicle and complete all necessary repairs free of charge (parts and labor).
Certain vehicles may have been assembled with an incorrectly manufactured Bendix MV-3 dash control valve. If the double check valve becomes lodged, in the event of a primary reservoir failure, air pressure can leak past the lodged valve, thereby depleting the secondary reservoir, causing a reduced ability for modulating the emergency brakes. Extended stopping distances may result in a vehicle crash, causing property damage, and/or personal injury or death. Correction: Dealers will inspect and, if necessary, replace the dash control valve.
A failure of this component (brakes) may increase the risk of a crash or injury.
Authorized dealerships will inspect the vehicle and complete all necessary repairs free of charge (parts and labor).
On certain trucks, an incorrectly manufactured steering gear sector shaft may cause the steering to "stick or bind". This could severely restrict the steering turning angle, possibly resulting in a vehicle crash with injury or death. Correction: Dealers will replace the steering gear assembly.
A failure of this component (steering) may increase the risk of a crash or injury.
Authorized dealerships will inspect the vehicle and complete all necessary repairs free of charge (parts and labor).
On certain trucks, the fifth wheel hitch assembly's lever arm may have been incorrectly installed during the manufacturing process. The lever arm pivot bolt may have been over-tightened which could distort the pivot bolt spacer sleeve and prevent the fifth wheel latch jaw from closing and latching securely around the trailer king pin. This could allow the towed unit to separate from the towing vehicle while underway, potentially causing a crash with injury or death. Correction: Dealers will replace the pivot bolt and sleeve with a hex head shoulder bolt and washer.
A failure of this component (other) may increase the risk of a crash or injury.
Authorized dealerships will inspect the vehicle and complete all necessary repairs free of charge (parts and labor).
On certain trucks, improper installation procedures may have damaged one or both locking tabs on the rear wheel spindle nut during vehicle assembly. Damage to the locking clip tabs reduces the nut's ability to resist rotation possibly allowing the nut to back off and the dual wheel set to become separated from the vehicle. If this happens, the vehicle may become difficult to control, leading to a crash with injury or death. In addition, the separated wheel assembly may pose a risk to other road users or bystanders. Correction: Dealers will inspect and replace damaged spindle nuts.
A failure of this component (wheels) may increase the risk of a crash or injury.
Authorized dealerships will inspect the vehicle and complete all necessary repairs free of charge (parts and labor).
On certain vehicles, the fasteners that attach the steering arm or tie rod arm to the spindle may have been over or under tightened during assembly process. Incorrectly torqued steering arm fasteners may fatigue and fracture, possibly causing a crash without warning. Correction: Dealers will inspect fasteners and apply correct tightening torque.
A failure of this component (steering) may increase the risk of a crash or injury.
Authorized dealerships will inspect the vehicle and complete all necessary repairs free of charge (parts and labor).
On certain vehicles, the internal rubber check valve inside the Bendix SR-7 spring brake modulating valve can become deformed over time. The effect of this defect is intermittent and presents a potential delay or failure in applying the parking brakes; potentially resulting in a vehicle roll away. Should this occur, the unattended roll away vehicle could strike a bystander or cause property damage. Correction: Dealers will install a check valve repair kit.
A failure of this component (brakes) may increase the risk of a crash or injury.
Authorized dealerships will inspect the vehicle and complete all necessary repairs free of charge (parts and labor).
Official Transport Canada safety campaigns, Canadian motor vehicle safety compliance standards and live VIN specifications.
Explore safety recall records by model year.