Safety defect investigations, technical specifications, and manufacturer repair notices for Canadian owners.
Enter a VIN to identify your vehicle and find Canadian recall notices that may apply to its make, model and year. Confirm VIN-specific eligibility and repair status with the manufacturer.
Switch to another Thomas Built Saf-T-Liner Efx School Bus model year.
Safety recall notices and repair campaigns registered for the 2016 Thomas Built Saf-T-Liner Efx School Bus in Canada.
On certain school bus seats, the plastic trim (bezel) where the shoulder seat belt comes out of the seatback may be too hard. Canadian regulations have requirements for anything that is installed in certain areas of the seatback. Note: This only affects school buses equipped with certain Syntec M2K and S3C passenger seats with lap/shoulder seat belts.
While this plastic trim is doesn't technically meet the requirements of Canadian regulations, it's unlikely to cause an injury.
This is not a recall. The company made changes in 2017, and all new seats made after that time have a soft vinyl cover trim for the shoulder seat belt.
Certain school buses may not meet Canadian regulations for roof panel joint strength.
A roof joint that is not strong enough could increase the risk of injury in a crash.
Daimler Truck North America (DTNA) will notify owners by mail and instruct you to take your bus to a DTNA authorized service facility to add additional fasteners to the roof lap joints.
This recall affects certain school buses equipped with SynTec S3B and/or S3C passenger seats. On some seats, the protective foam in certain areas of the seatback may not meet the knee impact requirements of Canadian regulations.
A seatback that does not have proper knee impact protection could increase the risk of injury to occupants in a crash.
The company will notify owners by mail and instruct them to take their vehicle to a Daimler Trucks of North America authorized service facility to install additional protective material in the seatbacks.
A problem with the left-rear brake caliper on certain school buses may cause the brake pads to drag and overheat. This could result in high temperatures, smoke, odour, or a possible fire.
A fire could increase the risk of injury. This could also result in an emergency evacuation of a school bus in an uncontrolled environment, which could also increase the risk of an injury.
The company will notify owners by mail and instruct them to take their vehicle to a Daimler Trucks North America authorized service facility to replace the left-rear brake caliper.
On certain school buses equipped with Syntec S3B restraint seats, under extreme operating conditions, such as adverse road conditions, repetitive shock loads, or occupant abuse, a metal fatigue crack may develop on the rear wall mount bracket of the seat. Over time, this could lead to the wall mount bracket fracturing, which in the event of a crash, could increase the risk of injury to seat occupants. Correction: Daimler Trucks of North America Service Facilities will inspect seats and install an additional wall bracket between the wall rail and the seat as necessary.
A failure of this component (seats and restraints) may increase the risk of a crash or injury.
Authorized dealerships will inspect the vehicle and complete all necessary repairs free of charge (parts and labor).
On certain school buses equipped with a Ricon S-Series wheelchair lift, the platform could potentially crack due to bent knuckle link arms and/or defective bearing. Overtime, the platform could separate of the rear portion of the pivot plate making the lift inoperable and putting the lift operator at risk of injury. Correction: Owners will need to make an appointment with the local Ricon Dealer to have the lift inspected and repaired.
A failure of this component (accessories) may increase the risk of a crash or injury.
Authorized dealerships will inspect the vehicle and complete all necessary repairs free of charge (parts and labor).
Certain school buses may not conform to Canada Motor Vehicle Safety Standard (CMVSS) 131 - School Bus Pedestrian Safety Devices. The STOP decal may not adhere properly to the stop sign and could peel off without warning, which could cause it to fail to meet the requirements of the standard. This could increase the risk of injury for the passengers exiting the school bus. Correction: Specialty Manufacturing Inc. will provide owners with a replacement stop sign blade assembly. If owners are not comfortable installing the blade assembly themselves, they can take their vehicle to a dealer for the installation.
A failure of this component (accessories) may increase the risk of a crash or injury.
Authorized dealerships will inspect the vehicle and complete all necessary repairs free of charge (parts and labor).
Certain school buses may fail to conform to Canada Motor Vehicle Safety Standard (CMVSS) 222 – School Bus Passenger Seating and Crash Protection. The SynTec S3B track seat may not provide sufficient strength to pass the rearward push test specified by the standard. In the event of a crash, the S3B track seat could come in contact with the passengers knees which could increase the risk of injury and/or impede egress. Correction: Dealers will install a “toe-clamp” on the feet of the S3B track mounted seat to meet the requirement of CMVSS 222.
A failure of this component (seats and restraints) may increase the risk of a crash or injury.
Authorized dealerships will inspect the vehicle and complete all necessary repairs free of charge (parts and labor).
Official Transport Canada safety campaigns, Canadian motor vehicle safety compliance standards and live VIN specifications.
Explore safety recall records by model year.