Safety defect investigations, technical specifications, and manufacturer repair notices for Canadian owners.
Enter a VIN to identify your vehicle and find Canadian recall notices that may apply to its make, model and year. Confirm VIN-specific eligibility and repair status with the manufacturer.
Switch to another GMC C Series model year.
Safety recall notices and repair campaigns registered for the 1996 GMC C Series in Canada.
Certain vehicles equipped with auto-apply park brakes may exhibit an unintended brake apply at speed due to a solenoid coil failure or some may exhibit a failure to release and/or be slow to apply or release due to water contamination. Correction: Dealers will seal the joint between the park brake reservoir and the pump assembly with Room-Temperature-Vulcanizing (RTV) sealant or inspect and replace any 10 volt park solenoids with a 12 volt solenoid.
A failure of this component (brakes) may increase the risk of a crash or injury.
Authorized dealerships will inspect the vehicle and complete all necessary repairs free of charge (parts and labor).
On certain crew cab pick ups, the front inner corner of the fuel tank may contact the body sill and over time wear a hole in or crack the fuel tank at the point of contact. This condition could result in fuel leakage and in the presence of an ignition source, a fire could occur. Correction: Tank will be inspected for wear and a spacer will be installed between the fuel tank and the front crossmember, or if necessary, the fuel tank will be replaced.
A failure of this component (fuel system) may increase the risk of a crash or injury.
Authorized dealerships will inspect the vehicle and complete all necessary repairs free of charge (parts and labor).
Certain vehicles may have windshield wiper motors with solder joints near the wiring harness connector that could crack. This could cause the windshield wiper to work intermittently and ultimately result in inoperative wipers. This could reduce driver visibility in inclement weather and result in a crash. Correction: Wiper motor circuit board and cover will be replaced.
A failure of this component (visual system) may increase the risk of a crash or injury.
Authorized dealerships will inspect the vehicle and complete all necessary repairs free of charge (parts and labor).
Certain vehicles do not comply with CMVSS 1103 - Exhaust Emissions. Vehicles may been built with the ignition coil wire too close to metal brackets or the transmission fluid fill tube (M/L van only). If the coil wire is too close to these metal objects, arcing may occur and cause failure of the wires which can in turn lead to a stalling/no start condition and/or catalytic converter failures. Correction: coil wire will be repositioned to assure adequate clearance from metal brackets and/or transmission fluid fill tubes.
A failure of this component (emissions) may increase the risk of a crash or injury.
Authorized dealerships will inspect the vehicle and complete all necessary repairs free of charge (parts and labor).
Certain vehicles exhibit a condition in which a pinch bolt exists in the recliner mechanism that could trap and pinch a person's hand or finger(s) when the easy entry feature is activated. This pinching could cut the hand or possibly sever the finger(s) without prior warning. Correction: a protector will be installed over the recliner mechanism.
A failure of this component (seats and restraints) may increase the risk of a crash or injury.
Authorized dealerships will inspect the vehicle and complete all necessary repairs free of charge (parts and labor).
On certain vehicles, the crankshaft balancer centre attaching bolt was under-torqued. This bolt secures the balancer, which is pressed onto the crankshaft, and the accessory drive pulley which is attached to the balancer, to the engine crankshaft. If this bolt were to loosen, the balancer and drive belt pulley would eventually loosen and the drive belt could come off the pulley or break, causing a loss of drive to engine accessories such as the alternator and power steering pump. Correction: Crankshaft balancer centre bolt will be torqued to specification.
A failure of this component (structure) may increase the risk of a crash or injury.
Authorized dealerships will inspect the vehicle and complete all necessary repairs free of charge (parts and labor).
Certain vehicles may have a bead damage to the tires which occurred during tire mounting. The damage to the tire reinforcing structure in the bead "toe" area would likely manifest itself as a bulge in the sidewall after the tire is inflated. This damage could result in rapid air loss, which could cause injuries to anyone if they were handling the tire when this occurred. Correction: Tires will be demounted and inspected for bead damage. If bead damage is present, the tire will be replaced.
A failure of this component (suspension) may increase the risk of a crash or injury.
Authorized dealerships will inspect the vehicle and complete all necessary repairs free of charge (parts and labor).
On certain vehicles, the four u-bolt nuts on either side of the rear axle may be under torqued. This could cause the bolts to loosen and eventually fall off the u-bolt. Should this occur, the axle would eventually be free to provide steering inputs to the vehicle and a crash could occur. Correction: Dealers will check the u-bolt nut torque and torque any loose u-bolts to specification.
A failure of this component (suspension) may increase the risk of a crash or injury.
Authorized dealerships will inspect the vehicle and complete all necessary repairs free of charge (parts and labor).
Certain vehicles may not comply with CMVSS 124 - Accelerator Control Systems. Vehicles may have been assembled with the throttle cable contacting the dash mat. The dash mat may bind the throttle cable such that the throttle return time may not meet the requirements of the standard. Correction: Dealers will inspect for adequate throttle cable to dash mat clearance, and if there is insufficient clearance, a portion of the dash mat will be cut out to provide clearance.
A failure of this component (other) may increase the risk of a crash or injury.
Authorized dealerships will inspect the vehicle and complete all necessary repairs free of charge (parts and labor).
Certain vehicles may experience a fuel leak at the fuel rail assembly end plug due to an improperly crimped end retainer clip. If this condition were to occur, and an ignition source was present, an engine compartment fire could occur. Correction: Defective fuel rail assemblies will be replaced.
A failure of this component (fuel system) may increase the risk of a crash or injury.
Authorized dealerships will inspect the vehicle and complete all necessary repairs free of charge (parts and labor).
Official Transport Canada safety campaigns, Canadian motor vehicle safety compliance standards and live VIN specifications.
Explore safety recall records by model year.